Install can be done with the hood on the Jeep still, or with the hood removed. We’ve done it both ways, and each have their pros/cons. For the majority of this install we’ll refer to doing it with the hood off. This procedure is done on a XJ/MJ Hood; however the basic practice can be done on your YJ/TJ/ZJ/WJ/JK etc. We’ve had great luck using them on many different models!

I stripped the hood of the material on the inside, and removed my engine light.

I than placed some tape in the area I was going to be working in. I did not want to scratch the hood (yes it’s the inside but still…). This would also allow me to draw my lines where I needed to cut.

I than placed the vents where I thought they looked and fit best.

I than placed the vent on the hood, and traced it with a pen.

Now, you’ll NOT want to cut on these lines, as if I did I would of cut to big of a hole. I measered aprox 3/8″ inside of this line and drew another line.

I also decided that since I was going to be cutting from the backside, I probally should place some tape on the other side to help prevent chipping.

We have found that a jigsaw with a nice metal blade works the best.

And both sides cutout

I had to make up some brackets. I ended up using 1/2 x 3/4 angle, and aprox 1.5″ long. I than drilled a hole in the center of the 3/4 side for the bolt. I used stainless hardware, to prevent rusting in the future.

One side installed.

Both installed, a view from the top.

And than re-installed the hood.

As stated prior we’ve also done the install on the Jeep without removing the hood. Very similar procedure;

Results? We’ve been very happy with the results. It helps keep the under-hood temperatures down quite a bit. This is especially helpful on those hot days your out wheeling and not a lot of air is going past your radiator due to a slow crawl. One of the biggest questions we get is what do you do about water? We’re happy to report that after 5+ years of running the vents we’ve had no damage to our motor/wiring due to any water. Many of our Jeep here at Motion are to “big” to fit into our garages and sit outside 365 days a year. No issues to report to date.

Interested in getting a set of hood vents? We sell there HERE.

Track Bar Relocation Brackets from JKS Manufacturing permanently correct geometry of the rear track bar following the installation of a CV-type driveshaft. The bolt-on bracket realigns the mounting point on the axle with the track bar and eliminates the binding problem caused by the rotated axle housing. As a result, the track bar and its bushings are returned to a neutral position and unwanted stresses are relieved from the mounting points.

Our Relocation Brackets also raise the mounting point on the axle to reduce track bar operating angles and minimize side-to-side axle movement. This improves vehicle stability on lifted vehicles at higher speeds and helps keep the axle centered beneath the chassis at all times. A heavy, steel crush-proof sleeve fits inside the factory bracket to ensure maximum torque can be applied to the mounting hardware without risk of loosening or distortion over time.

Product Features:

• Heavy-duty reinforcement bracket mounts directly to factory track bar bracket on axle housing
• Angled design corrects rear track bar geometry on lifted vehicles that have rotated axle housing or CV-type driveshaft
• Relocated mounting point tilts forward to eliminate binding and premature bushing wear
• Premium steel construction is laser cut, formed and folded for maximum strength
• Economical bolt-on solution minimizes risk of track bar failure on the trail

More Info Available Here: http://motionoffroad.com/catalog/index.php?main_page=product_info&cPath=13_30_233&products_id=2757

Bushwacker’s new Flat Fender flares for Jeep YJ Wranglers set the standard for flat-fenders in style, function, and durability. The newly designed flare offers more clearance for taller, wider tires by eliminating the factory flare’s overhang and extending a full six inches from the body. Made of extreme-duty TPO plastic that’s more durable and flexible than ABS, the flares are guaranteed not to sag like urethane flares, or chalk like factory flares. Plus, they’re the only flat-fender flares to include a DOT side marker light and reflector, keeping your Jeep street legal. And the fit and finish is outstanding, making them the best looking and best designed flares on the market. If you’ve got a Jeep YJ, check out Bushwacker’s new flares today!

Features:

• Adds additional coverage, great for large wheel and tire packages
• Includes 50-state legal LED marker light!
• Easy No-Drill installation process
• 100% UV protection. No chalking, No cracking, No warping
• Extreme TPO material gives maximum durability and flexibility
• OEM matte black finish, or easily custom painted to match or accent any vehicle

Check them out at MotionOffroad.com here: http://motionoffroad.com/catalog/index.php?main_page=product_info&cPath=51_350_85&products_id=2703

We’ve just taken shipment of more Surco inventory! Due to the popular demand of the 45″ x 60″ and the constant request for additional sizes we’ve now started to carry the full Surco Roof Rack & Accessories for the rack’s in stock!

We’ve had great luck with our Surco roof racks over the past few years. These Surco Safari basket racks mount to your factory roof rack, multi-rack system, or rain gutters, and allow you to store cargo more securely. Features include durable 3/4 in. square aluminum tubing construction (NO RUST!), a black powdercoat finish, a sturdy aluminum floor, and an easy installation with no drilling required.

Checkout our expanded line of Surco products here: http://motionoffroad.com/catalog/index.php?main_page=index&manufacturers_id=51

Due to the popularity of our JK radio mounts we’ve now got them available for the TJ! Easily mount a CB radio in your TJ Wrangler. The easiest TJ Wrangler CB mount to install on the market! Can be mounted and ready within 10 minutes. Allows you to store your CB up out of the way without obstructing the view of the rearview mirror. Mounts to windshield using existing holes. A right angle coax adapter is also supplied so the CB can be mounted as close to the windshield as possible. Will work with hard or soft top. High quality stainless steel construction. Designed to work with smaller radio’s like our Cobra 19 Ultra III CB. Lazer cut and precision bent for a perfect fit every time. Fits all model TJ’s from 1997-2006. MADE IN THE USA!

More information and photo’s can be found here: http://motionoffroad.com/catalog/index.php?main_page=product_info&cPath=304&products_id=2545

Finally available! You’ve asked for them, we’ve delivered! Works great in a SOA application!

These springs are factory replacement stock 4wd springs and mount under the axle just like the originals. They will give no lift over stock. They have 3 leaves plus the 1 overload leafs (3+1 style) and are equipped with O.E.M. type rubber bushings. These ONLY fit the MJ Comanche’s (will not fit the XJ) and fit both the SWB and LWB models. We have these made for us in the USA to our specs! Backed by our LIFETIME WARRANTY!

Sold as a set (2 leafs).

More Info Here: http://motionoffroad.com/catalog/index.php?main_page=product_info&cPath=13_26_332&products_id=2542

Notes:

• Fits 84-01 Jeep XJ Cherokee models ONLY.
• Adds approximately 1″-1.5″ of lift.
• Longer rear shocks are recommended.
• A taller coil or coil spacers in the front are recommended to level the vehicle.
• Exhaust modifications may be required for adequate clearance of the shackle bracket.

Benefits:

• Fine tune the rear suspension of your XJ.
• Places shackle in optimum location for maximum articulation.
• Allows for greater articulation off-road.

Kit Contents:

• Rear: Frame brackets, shackle brackets and hardware.

Install Video:

Available from MotionOffroad.com here: http://motionoffroad.com/catalog/index.php?main_page=product_info&cPath=13_27&products_id=2537

The all-new 2.0 Factory Performance Series Shocks give you legendary FOX performance in an ultra heavy duty, bolt-on package. This all-new shock features a high-flow piston, deflective disc technology, and an Internal Floating Piston (IFP) that creates a perfect racing-oil/air separation to provide incredible fade-free damping performance giving you precise handling, control and stability. The 6061-T6 one-piece body and billet rod end, stout 5/8″ shaft, and anodized components ensure the 2.0 Factory Performance Series unsurpassed durability.

Available for the Jeep Wrangler JK, Wrangler TJ, Grand Cherokee ZJ, Cherokee XJ, and Comanche MJ.

View the full line here: http://motionoffroad.com/catalog/index.php?main_page=advanced_search_result&search_in_description=1&keyword=Fox+2.0%22+Factory+Performance+S&x=0&y=0

Transamerican Auto Parts/4 Wheel Parts announced today in a press-release that they have finalized the acquisition of Rubicon Express.

Transamerican Auto Parts/4 Wheel Parts is proud to announce the acquisition of Rubicon Express.

Inspired by the famous Rubicon trails of Northern California, Rubicon Express has a long history of manufacturing hard-core performance suspension systems. Off-road enthusiasts the world over have come to trust Rubicon Express to be the ultimate suspension system for their Jeeps.

Customer feedback has been overwhelming, and we are committed to getting this fantastic brand back in the marketplace quickly. Furthermore, we pledge to use the same manufacturing process that Rubicon has had for years. All products will continue to be made in USA. We are working closely with many members of Rubicon’s team to ensure, long into the future, the same respected quality you’ve come to expect throughout the entire product line.

Today, our goal is to have product available for purchase by August 1, 2011. Our first priority, though, is to you, all the loyal Rubicon customers. Please be assured that we will gladly honor any and all warranty requests, and replacement parts will soon be available. We will continue to partner with Rubicon’s off-road jobbers and distributors.

Soon you will find high quality Rubicon Express in stock at your favorite dealer and out on the trails. We appreciate your interest in Rubicon Express and your understanding while we work to re-establish the one and only Rubicon Express.

Greg Adler
President & CEO
Transamerican Auto Parts/4 Wheel Parts

Source: RubiconExpress.com

We’ve got some big news to share: Our new line of winches start at $399 after an $80 mail-in rebate. Plus, many have new features for increased performance, reliability, and durability.

The all-new WARN VR Series includes the VR8000, VR10000, and VR12000 with 8,000, 10,000, and 12,000 lb. capacities, respectively. All of these units feature series-wound motors for plenty of power; brakes that hold the full-rated load for great control while winching; three-stage planetary geartrains for speed, durability, and reliability; corded remote controls; and 94-feet of durable wire rope. All of these winches are backed by the WARN limited lifetime warranty, too. You can purchase a WARN VR8000 for $399 after the $80 mail-in rebate.

It’s not just the VR that’s newsworthy, though. Most winches in the WARN Premium Series, Ultimate Performance Series, and Heavyweight Series now feature contactor control for increased durability and reliability; redesigned control housings; and a new-and-improved remote control that is more durable, reliable, and easy-to-use than ever.

View the new WARN VR Entry Level Series Winches on MotionOffroad.com by CLICKING HERE.